Saturday, October 8, 2011

Deer Antler Hair Clips

These three hair decoration projects are all similar, but I have used slightly different fasteners and horn / wing / antler shapes for each. You are really only limited by your imagination with these projects. I can see unicorn horns or elephant ears easily made using the same instructions. I think I might be in love with FIMO air for microwave. I don't know how I ever crafted without it!

Things you'll need to make the Deer Antler Hair Clips:

1 package of FIMO air for the microwave
Basic sculpting tools
Black brown and white acrylic craft paint
Craft paint brushes (Soft or stiff bristle will both work, use what you have.)
Hot glue gun and glue sticks
Black maribo or the soft fuzzy part of a black feather
2 large snap clips
Black felt
scissors
microwave
small tub of water



Roll out some of the FIMO air for microwave (henceforth called clay!) into a 3cm thick worm. Cut two pieces that are 6cm long from the worm. Roll one end of each of the worms until they form cone shapes. Continue rolling the cones until they resemble long sticks. Add smaller sticks to the sides of these original sticks creating forks in the branch. I added four branch tips in all but there isn't really a set formula. I just tried to keep the shapes similar between the two antlers.

When you're happy with them place them on a microwaveable tray lined with parchment paper. Fill a microwaveable cup up half full with water and place it in the microwave with the tray of antlers. Microwave according to the manufacturers instructions. (Do read them, they help!) I microwaved my two horns for 3 to five minutes. I didn't notice a big difference in the curing time between the wing project that was thin clay and the antler project that was a thicker piece. I think all that mattered was I used roughly the same mass of product for both projects. It worked GREAT!!! No more waiting for clay to air dry!

*Important*
FIMO air microwaveable is a COMPLETELY different product than FIMO polymer clay. Both are really great products but the curing instructions are completely different and should never be confused.

FIMO Air is a very lightweight, air dry water based clay.

FIMO polymer clay is a heat cured product.

I love them both!!!!


Base coat each antler with an even coat of brown acrylic paint and let them dry.



Mix some lighter brown paint by mixing the white and brown together. Dab a small amount of this new light brown paint onto your brush and with a light touch, tickle some of this lighter paint over the dark brown. You will see some of the dark brown showing through the new light brown layer. Don't paint the lighter brown right down to the base of the antlers. Leave some of the darker brown showing there too.

Add a small bit of white paint to the very tips of each antler end. Let the antlers dry.



Paint some black lines from the bottom of each antler trailing off thinly into the middle of each antler. Shade one side of each of these black lines with a bit of brown paint to give some depth and shadow. Let the antlers dry.


Gather together your glue gun and glue sticks, dry antlers, clips, felt bits and feathers.


Cut two circles of felt the same size as the base of each antler and two 1/2cm strips of felt as long as the circles are wide. Place the strips of felt into the opened clips and glue a circle on to the top of them. Make sure the small "tongue" of the clip is on the bottom.


Glue the feathers around the edge of each felt round and an antler to the middle of the top of each felt round. Again, make sure the small "tongue" part of each clip is on the bottom and make sure to angle the antlers evenly on each clip so that when you are wearing them they point in opposing directions.

I want to make more of these. It's kind of addicting.
Hope you love them too!
Happy creating!


3 comments:

Anonymous said...

I love these, even more than the demon horn ones! I'm so going to convince my husband to help me make some!

from Kellie said...

Awesome!
I warn you though....
You'll want to wear them everywhere.


:D

Anonymous said...

I make clip on ears, but I always have issues when it comes to gluing the ears to clips. Next time, I'm going to give your felt method a try and see if that works better! Really helpful!